Troubleshooting Causes And Remedies
If your firearm is properly used and maintained, malfunctions will rarely occur. However, if such a situation does occur please observe the following instructions.
CAUTION - if a malfunction occurs, the possibility of an unintentional discharge is substantially increased. For this reason, when clearing malfunctions, observe the Safety Instructions already mentioned above. Keep the rifle pointed in a safe direction, do not turn the rifle against your body or anyone else's. Do not place your hands in front of the barrel!
|
Malfunction |
Possible Cause |
Remedy |
|
A round has not been fed into the chamber. |
Magazine is not fully inserted or is damaged. The rifle or cartridges are fouled (dirty). |
Insert magazine properly or change magazine. Clean the rifle and cartridges and wipe them dry or as the case may be slightly lubricate. |
|
Firing Pin hole fouled (dirty) or improper lubrication agent used during low temperatures conditions. |
Follow the Safety Instructions according to point 19. Disassemble and clean the firing pin or use low temperature lubricant. | |
|
A shot sounds "weak". |
The primer has been activated but no powder load was inside the cartridge case. |
Unload the rifle and check that the bullet is not lodged in the barrel. Any subsequent shot could cause damage to the barrel! |
|
The spent case has not been ejected. |
Cartridge chamber, extractor or ammunition dirty or unsuitable lubricant in low temperature environment. |
Clean and wipe the rifle dry or eventually lubricate lightly with a suitable agent. Use clean and new ammunition. |
If you cannot clear away any malfunction in the manner described above, entrust the rifle to a competent gunsmith for inspection and repair.
- ILLUSTRATION AND LIST OF PARTS
|
1 Barrel |
30 Plunger Pin |
|
2 Rear Sight |
31 Safety |
|
32 Safety Pawl | |
|
4 Front Sight Base |
33 Safety Pawl Spring |
|
5 Front Sight Base Screw 05 |
34 Roller |
|
6 Front Sight Base Screw 03 |
35 Safety Pawl Pin |
|
7 Rear Sight Base Screw |
36 Sear |
|
8 Front Sight Detent |
37 Sear Stop |
|
9 Detent Spring |
38 Sear Spring |
|
10 Pin, Front Sight Detent |
39 Sear Pin |
|
11 Front Sight Cover |
40 Bolt Stop |
|
12 Receiver | |
|
13 Bolt |
42 Safety Pin |
|
14 Bolt Handle Knob |
43 Retaining Plate |
|
15 Extractor |
44 Ejector |
|
16 Extractor Collar |
45 Ejector Pin |
|
17 Firing Pin |
46 Ejector Spring |
|
18 Firing Pin Spring |
47 Ball |
|
19 Support, Firing Pin Spring |
48 Trigger Housing |
|
20 Nut, Firing Pin Spring |
49 Trigger |
|
50 Trigger Lever | |
|
22 Pin, Firing Pin Nut |
51 Trigger Lever Pin |
|
23 Cap |
52 - |
|
24 Bolt Sleeve |
53 Adjusting Screw, Set |
|
25 Disassy Catch |
Trigger |
|
26 Disassy Catch Spring |
54 Set Trigger Lever |
|
27 Disassy Catch Pin |
55 Spring, Set Trigger Lever |
|
28 Disassy Catch Plunger |
56 Pin |
|
29 Plunger Spring |
57 Retaining Ring |
rRUCTION MANUAL
58 Adjusting Screw (B)
59 Spring, Trigger Pull
60 Adjusting Screw, Trigger Pull (A)
61 Locking Nut
62 Adjusting Screw, Trigger Overtravel (C)
63 Locking Nut
64 Nylon Pin (2x)
66 Screw
67 Spring Washer
68 Stock
69 Butt Plate Spacer
70 Butt Plate
71 Screw, Butt Plate
72 Butt Plate Plug
73 Swivel Wood Screw
74 Sling Swivel
75 Swivel Screw
76 Swivel Screw Washer
77 Swivel Assembly
78 Trigger Guard - Box Version
79 Box Shell
80 Floor Plate
81 Floor Plate Pin
82 Floor Plate Latch
83 Spring, Floor Plate Latch
84 Pin, Floor Plate Latch
85 Magazine Box Spring
87 Front Spacer
88 Frame Screw, Front
89 Rear Spacer
90 Frame Screw, Rear 106 Trigger Spring
The following parts relate to the detachable magazine version
91 Trigger Guard - Magazine Version
92 Magazine Latch
93 Magazine Latch Spring
94 Magazine Latch Pin
96 Magazine Catch Spring
97 Magazine Catch Pin
98 Magazine Shell
99 Magazine Floor Plate
100 Floor Plate Lock
101 Magazine Spring
102 Follower
103 Magazine Ejector
104 Magazine Ejector Spring
105 Magazine Ejector Pin
|
Model |
Standard, Lux, MC Minnesota American Prestige * Scandinavia |
Battue |
Sport |
Varmint | |
|
Calibers, Magazine |
.243 Winchester .308 Winchester .22-250 Remington |
.243 Winchester .308 Winchester .22-250 Remington |
.308 Win. |
.243 Win. .308 Win. .22-250 R. | |
|
Calibers, Magazine Box |
6,5x55 SE .270 Winchester 7x57 7x64 .30-06 Springfield 9,3x62 |
6,5x55 SE .270 Winchester 7x57 7x64 .30-06 Springfield 9,3x62 |
- | ||
|
Overall Length |
[mm] |
1135 |
1055 |
1150 |
1185 |
|
Barrel Length |
[mm] |
600 |
520 |
650 |
650 |
|
Sights Radius (Mechanical Sights) |
[mm] |
420 |
340 |
- |
- |
|
Weight (Empty Magazine) |
[kg] |
3,3 |
3,1 |
4,7 |
4,2 |
|
Capacity [cartridges] Magazine Box / Magazine Long / Magazine Short |
5 / 4 / 3 |
5 / 4 / - |
- I 4 I - |
- I 4 I - | |
|
Trigger Pull, Adjustment Range |
[N] |
12 -22 |
12 -22 |
12 - |
-22 |
* only with fixed magazine versions in .270 Winchester and 30-06 Springfield calibers
* only with fixed magazine versions in .270 Winchester and 30-06 Springfield calibers
Average user rating: 5 stars out of 1 votes
Post a comment